
Metal surface finishing and part restoration in Utah
Dozti Metal grinds, deburrs, cleans and polishes metal parts for manufacturers, machine shops and other businesses, and brings worn parts back into service. We do every job in our own shop.
- Drawing, photo or sampleReviewed before we quote, with a written quote to follow
- First piece for approvalOn batches, you see one finished part before the rest
- Monday to Friday7:30 AM to 6:00 PM, at the bench in Iron County
The finish ladder: pick the rung your part needs
Most parts reach us near the bottom rung. Each step up takes the surface further, and each one has a job. Slide or tap through the five rungs to see how the sample plate changes and why the step is there.
As received
Mill scale, light rust, handling marks and sharp cut edges. This is how bar stock, laser-cut blanks and older parts usually reach us.
Why this step: We read the starting surface first. It tells us how much work the next rungs will take and where to begin.
Surface work and restoration under one roof
Two kinds of work share the same benches. Surface work takes new or stock parts up the ladder to the finish you need. Restoration and repair take worn items back down to sound metal and bring them up again.
Surface work
- Surface preparationScale, rust and tired old finish taken off mechanically, so the metal is clean and ready for paint, powder coat or the next step.
- GrindingHigh spots, rough edges and heavy marks ground back to a flat, even surface, shaped for the finish that comes next.
- DeburringBurrs taken off cut edges, holes and slots, and every edge softened, so parts handle safely and fit cleanly.
- PolishingSatin, brushed or mirror finishes on steel, stainless, aluminum and brass parts that people see and touch.
Businesses that send us parts
Our customers are companies, from one-person design studios to plants with steady production. What they share is a part that needs a better surface or a second life.
Manufacturers and machine shops
Runs of cut or machined parts that need deburring and a consistent finish before they ship.
Equipment builders
Covers, guards, panels and frames finished before assembly, so the machine looks as good as it works.
Design and architectural studios
Decorative pieces and trim brushed or polished to the sample on your board.
Restaurants, shops and offices
Worn stainless panels, fixtures, plates and hardware repaired and refinished.
Distributors
Repeat batches of parts finished the same way every time, from the approved first piece.
Start-ups and product teams
Prototype parts finished for a demo, a photo shoot or a first customer.

How we handle a job, step by step
Send photos, a drawing or a sample
Use the form or email us. Tell us the metal, the quantity and the finish you are after. Photos from a phone are fine.
Get a written quote
We review what you sent, ask about anything unclear and reply with a written quote. Tolerances and critical sizes are confirmed there.
Approve the first piece
On batches we finish one part first. You see it, hold it and approve it before the rest are done.
Collect finished parts
The batch follows the approved piece. Parts are wrapped and boxed so the finish stays clean on the way back.

Not sure what to ask for?
Finish names get used loosely. One shop's satin is another shop's brushed. Our finish guide explains each rung in plain words, shows which finish suits which kind of part, and gives you the phrases that make a request clear the first time.
If you already have a part with a finish you like, that is even better. Send it with your request and we will match it.
Read the finish guideWhat to include in a request
A few details let us quote without a long back and forth. Phone photos are fine, and you can email drawings after you send the form.
- What the part is and the metal it is made of
- How many pieces, and whether it repeats
- The starting surface and the finish you want
- A drawing, photos or a sample, if you have one
- When you would like the parts back
We work with businesses in Iron County and nearby Washington County communities. Parts can be dropped off during opening hours or shipped to the shop.
Common questions
Do you work with private individuals?
Our shop works with businesses: manufacturers, machine shops, equipment builders, studios, distributors and commercial customers such as restaurants and stores.
Do you do all the work in your own shop?
Yes. Every job is done at our benches and machines in the shop. You drop parts off or ship them, and collect them when they are finished.
What metals do you work on?
Carbon steel, stainless steel and aluminum make up most of our work, with brass and other metals by arrangement. Tell us what you have.
Do I need a drawing?
A drawing helps, but it is not required. Clear photos or a sample part are often enough for us to understand the job and quote it.
Have parts that need a better surface?
Send photos, a drawing or a sample with the metal, the quantity and the finish you want. You get our questions or a written quote back.
